The first real cold snap of the season has a way of revealing which heating systems did not survive the summer. You turn up the thermostat, nothing happens, and the house keeps getting colder. Before you assume the worst, there are seven quick checks that solve a surprising number of “no heat” calls, and a clear set of signs that mean it is time to stop troubleshooting and call a professional.
Cooling By Design is headquartered at 21201 Victory Blvd, Suite 125, Canoga Park, CA 91303. Licensed (#1148982), a certified Mitsubishi Electric Diamond Dealer, with 24-hour emergency service available. Call (877) 702-6654 for furnace and heating repair across Canoga Park and the surrounding neighborhoods.
Safety First
- If you smell gas (rotten eggs), do not touch anything. Leave the home and call SoCalGas at 1-800-427-2200 or 911 from outside.
- Do not remove sealed panels, bypass safety switches or attempt gas or electrical repairs yourself.
- If a carbon monoxide alarm sounds, get everyone outside and call 911.
The 7 Checks Before You Call
1. Check the thermostat
Confirm it is set to HEAT (not COOL or OFF) and the target temperature is a few degrees above the current room temperature. Replace the batteries if the display is blank or dim. With a smart thermostat, check that it is online and has not reverted to a schedule or an “away” mode.
2. Check the power
Furnaces usually have a switch that looks like an ordinary light switch on or near the unit. Make sure it is on. Then check your electrical panel for a tripped furnace breaker. If a breaker trips again right after you reset it, stop and call a technician.
3. Make sure the access panel is seated
Many furnaces have a safety switch that cuts power when the blower door is not fully closed. If you recently changed the filter, confirm the panel is back in place and latched.
4. Inspect the air filter
A clogged filter can cause the furnace to overheat and shut itself off for safety, or restrict airflow enough that it will not run properly. Replace it if it looks gray or blocked. Our guide to maintenance you can safely do yourself explains how to check and change one.
5. Confirm the vents and returns are open
Blocked supply registers and return grilles reduce airflow and can trigger safety shutoffs. Move furniture, rugs and boxes away from them.
6. Check the gas supply
If your stove or water heater works, gas is reaching the home. Near the furnace, the gas shutoff valve handle should be parallel to the pipe when open. If your furnace has a standing pilot light and it is out, follow the manufacturer’s relighting instructions printed on the unit. Never try to relight it if you smell gas. Most modern furnaces use electronic ignition instead.
7. Look for a drain or error code
High-efficiency furnaces have a condensate drain, and a clogged drain can trip a safety switch and shut the system down. Many furnaces also have a small window on the control board with a blinking LED. Note the flash pattern or code, which helps a technician diagnose the issue faster.
Using a Heat Pump Instead of a Furnace?
If your home is heated by a heat pump, the same basics apply, with a few differences. Make sure the thermostat is in HEAT mode and not in emergency heat unless you intend it to be. Check breakers for both the indoor and outdoor units. A frosty outdoor unit that periodically steams or pauses can simply be in normal defrost mode, but heavy ice buildup that does not clear needs a technician. If you are considering one, our guide to heat pumps versus AC plus a furnace explains the tradeoffs.
When to Stop Troubleshooting and Call a Pro
- The furnace clicks or tries to start but never ignites
- It starts, runs briefly and shuts off repeatedly (short cycling)
- You hear banging, squealing or grinding
- The breaker trips more than once
- You see water leaking around the furnace
- You notice a burning, electrical or gas smell. Our guide to the furnace burning smell on first start explains which odors are harmless and which are urgent.
- Anyone in the home, especially an infant, an older adult or someone with health concerns, is cold and the temperature is dropping
Cooling By Design offers 24-hour emergency service. See how our same-day emergency service works, what to expect from fast repair service, and what a service call typically costs. Before you hire anyone, read what to ask a technician and the red flags to watch for.
Staying Warm While You Wait
- Use a space heater only if it has automatic tip-over and overheat shutoff, plug it directly into a wall outlet (not an extension cord), and keep it at least three feet from anything flammable.
- Never use a gas oven, stove, grill or generator indoors to heat your home. They can produce deadly carbon monoxide.
- Close doors to unused rooms and layer clothing and blankets to retain heat in the room you are using.
Prevent the Next No-Heat Surprise
Most “furnace will not turn on” calls trace back to a dirty filter, a worn part or maintenance that was skipped. A pre-season inspection catches these before the cold arrives. See what a proper tune-up includes, follow our HVAC maintenance checklist, and ask about maintenance plans that schedule seasonal visits automatically. If the furnace is old and repairs keep adding up, our repair-or-replace decision guide and the latest LADWP and California HVAC rebate rules can help you plan. If smoke or poor air quality is also a concern, see our tips for protecting your indoor air.
Our Service Area
Cooling By Design provides furnace and heating repair, emergency service and maintenance from our Canoga Park headquarters across:
- Canoga Park
- Winnetka
- Woodland Hills
- West Hills
- Tarzana
- Reseda
- Chatsworth
- Northridge
- Hidden Hills
- Bell Canyon
- Calabasas
- Lake Balboa
- Porter Ranch
- Encino
- North Hills
- Granada Hills
- Topanga
- Van Nuys
- Panorama City
- Mission Hills
- Sherman Oaks
Frequently Asked Questions
Why won’t my furnace turn on when I turn up the thermostat?
The most common causes are thermostat settings or dead batteries, a tripped breaker or switch, a loose access panel, a clogged filter, a closed gas valve or a safety lockout. Run through the checks above before calling.
Why does my furnace click but not ignite?
Clicking without ignition can point to a failed igniter, a flame sensor problem, a gas supply issue or a control board fault. That is a job for a licensed technician.
Is it safe to reset my furnace?
Turning the power off and back on at the switch is a common first step, but repeated resets or resetting safety switches can hide a serious problem. If it fails again, call a professional.
Can a dirty filter stop my furnace from working?
Yes. A clogged filter restricts airflow, which can cause the furnace to overheat and shut down on a safety limit.
What should I do if I smell gas?
Do not use switches, lighters or phones inside. Leave the home and call SoCalGas at 1-800-427-2200 or 911 from outside.
Do you offer emergency furnace repair in Canoga Park?
Yes. Cooling By Design offers 24-hour emergency service for Canoga Park and the surrounding neighborhoods listed on this page.
No Heat? Call Us Now
If you have worked through the checks and the furnace still will not run, our licensed technicians are ready to help. Read our frequently asked questions or ask about maintenance plans. Call (877) 702-6654 or schedule online here. Email office@coolingbydesign.com. License #1148982. 21201 Victory Blvd, Suite 125, Canoga Park, CA 91303.
